it would be great if we could add a BT-Dongle to the Scroll 7" tab. I tried three different sticks without success.
The Dmesg output :
- Code: Select all
<4>[20233.990000] usb disconnected.
<4>[20246.590000] Set ID to host mode(0)
<4>[20246.590000] SRP: Device mode
<4>[20246.620000] ID change ISR : Host (0)
<4>[20246.710000] Using Buffer DMA mode
<4>[20246.710000] Periodic Transfer Interrupt Enhancement - disabled
<4>[20246.720000] Multiprocessor Interrupt Enhancement - disabled
<4>[20246.770000] Init: Port Power? op_state=1
<4>[20246.770000] Init: Power Port (0)
<3>[20246.770000] DWC_OTG : [tcc_set_vbus] vbus_state:1
<6>[20255.320000] usb 2-1: new high speed USB device using dwc_otg and address 4
<6>[20255.520000] hub 2-1:1.0: USB hub found
<6>[20255.530000] hub 2-1:1.0: 4 ports detected
<6>[20255.820000] usb 2-1.4: new high speed USB device using dwc_otg and address 5
<6>[20255.920000] hub 2-1.4:1.0: USB hub found
<6>[20255.930000] hub 2-1.4:1.0: 4 ports detected
<6>[20263.950000] usb 2-1.4.3: new low speed USB device using dwc_otg and address 6
<3>[20264.070000] usb 2-1.4.3: device v1ddd p1005 is not supported
<6>[20264.100000] input: SIGMACHIP USB Keykoard as /devices/platform/dwc_otg.0/usb2/2-1/2-1.4/2-1.4.3/2-1.4.3:1.0/input/input8
<6>[20264.120000] generic-usb 0003:1DDD:1005.0005: input: USB HID v1.10 Keyboard [SIGMACHIP USB Keykoard] on usb-dwc_otg.0-1.4.3/input0
<6>[20264.520000] input: SIGMACHIP USB Keykoard as /devices/platform/dwc_otg.0/usb2/2-1/2-1.4/2-1.4.3/2-1.4.3:1.1/input/input9
<6>[20264.640000] generic-usb 0003:1DDD:1005.0006: input: USB HID v1.10 Mouse [SIGMACHIP USB Keykoard] on usb-dwc_otg.0-1.4.3/input1
<6>[20275.990000] usb 2-1.4.2: new full speed USB device using dwc_otg and address 7
<3>[20276.090000] usb 2-1.4.2: device v1131 p1004 is not supported
<6>[20282.410000] usb 2-1.4.2: USB disconnect, address 7
<6>[20289.040000] usb 2-1.4.2: new full speed USB device using dwc_otg and address 8
<3>[20289.140000] usb 2-1.4.2: device v1310 p0001 is not supported
<6>[20293.660000] usb 2-1.4.2: USB disconnect, address 8
<6>[20298.520000] usb 2-1.4.2: new full speed USB device using dwc_otg and address 9
<3>[20298.800000] usb 2-1.4.2: device v0a12 p0001 is not supported
<6>[20302.360000] usb 2-1.4.2: USB disconnect, address 9
<4>[20305.720000] Set ID to device mode(0)
<4>[20305.720000] usb connected.
<6>[20305.750000] usb 2-1: USB disconnect, address 4
<6>[20305.750000] usb 2-1.4: USB disconnect, address 5
<6>[20305.750000] usb 2-1.4.3: USB disconnect, address 6
<4>[20305.760000] ID change ISR : Device (0)
<4>[20305.760000] Using Buffer DMA mode
<4>[20305.770000] Periodic Transfer Interrupt Enhancement - disabled
<4>[20305.770000] Multiprocessor Interrupt Enhancement - disabled
<4>[20305.780000] Using Buffer DMA mode
<4>[20305.780000] Periodic Transfer Interrupt Enhancement - disabled
<4>[20305.780000] Multiprocessor Interrupt Enhancement - disabled
<3>[20305.800000] DWC_OTG : [tcc_set_vbus] vbus_state:0
<4>[20305.930000] usb disconnected.
<4>[20307.320000] SRP: Device mode
<4>[20307.400000] usb connected.
<4>[20307.520000] USB RESET
<4>[20307.570000] USB RESET
<6>[20307.650000] android_usb gadget: high speed config #1: android
<4>[20344.280000] AR6000 Neighbor Report Event
The USB Hub and the keyboard is working fine.
Anyone got a clue if it will be possible to add bt drivers ?
Sensi
